Safety Instruction
These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss.
The precaution measure is divided into Dangers and Cautions:
Dangers: Neglecting any of the warnings may cause serious injury or death.
Cautions: Neglecting any of the cautions may cause injury or equipment damage.
 |
|
|
Dangers: Follow these safeguards to prevent serious injury or death. |
Cautions: Follow these precautions to prevent potential injury or material damage. |
Danger:
-
All the electronic operation should be strictly compliance with the electrical safety regulations, fire prevention regulations and other related regulations in your local region.
-
This equipment is intended to be supplied from the Class 2 surge protected power source rated DC 12V, 2A.
-
Do not connect several devices to one power adapter as adapter overload may cause over-heat or fire hazard.
-
Please make sure that the power has been disconnected before you wire, install or dismantle the device.
-
When the product is installed on wall or ceiling, the device shall be firmly fixed.
-
If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center.
-
If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the device yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.)
Cautions:
-
Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage).
-
Do not place the device in extremely hot (refer to the specification of the device for the detailed operating temperature), cold, dusty or damp locations, and do not expose it to high electromagnetic radiation.
-
The device cover for indoor use shall be kept from rain and moisture.
-
Exposing the equipment to direct sun light, low ventilation or heat source such as heater or radiator is forbidden (ignorance can cause fire danger).
-
Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfunction however), and affecting the endurance of sensor at the same time.
-
Please use the provided glove when open up the device cover, avoid direct contact with the device cover, because the acidic sweat of the fingers may erode the surface coating of the device cover.
-
Please use a soft and dry cloth when clean inside and outside surfaces of the device cover, do not use alkaline detergents.
-
Please keep all wrappers after unpack them for future use. In case of any failure occurred, you need to return the device to the factory with the original wrapper. Transportation without the original wrapper may result in damage on the device and lead to additional costs.
-
Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer.
-
Biometric recognition products are not 100% applicable to anti-spoofing environments. If you require a higher security level, use multiple authentication modes.
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss.
The precaution measure is divided into Dangers and Cautions:
Dangers: Neglecting any of the warnings may cause serious injury or death.
Cautions: Neglecting any of the cautions may cause injury or equipment damage.
|
|
|
Dangers: Follow these safeguards to prevent serious injury or death. |
Cautions: Follow these precautions to prevent potential injury or material damage. |
Danger:
-
All the electronic operation should be strictly compliance with the electrical safety regulations, fire prevention regulations and other related regulations in your local region.
-
This equipment is intended to be supplied from the Class 2 surge protected power source rated DC 12V, 2A.
-
Do not connect several devices to one power adapter as adapter overload may cause over-heat or fire hazard.
-
Please make sure that the power has been disconnected before you wire, install or dismantle the device.
-
When the product is installed on wall or ceiling, the device shall be firmly fixed.
-
If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center.
-
If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the device yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.)
Cautions:
-
Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment installation on vibrations surface or places subject to shock (ignorance can cause equipment damage).
-
Do not place the device in extremely hot (refer to the specification of the device for the detailed operating temperature), cold, dusty or damp locations, and do not expose it to high electromagnetic radiation.
-
The device cover for indoor use shall be kept from rain and moisture.
-
Exposing the equipment to direct sun light, low ventilation or heat source such as heater or radiator is forbidden (ignorance can cause fire danger).
-
Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfunction however), and affecting the endurance of sensor at the same time.
-
Please use the provided glove when open up the device cover, avoid direct contact with the device cover, because the acidic sweat of the fingers may erode the surface coating of the device cover.
-
Please use a soft and dry cloth when clean inside and outside surfaces of the device cover, do not use alkaline detergents.
-
Please keep all wrappers after unpack them for future use. In case of any failure occurred, you need to return the device to the factory with the original wrapper. Transportation without the original wrapper may result in damage on the device and lead to additional costs.
-
Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer.
-
Biometric recognition products are not 100% applicable to anti-spoofing environments. If you require a higher security level, use multiple authentication modes.