Add Access Control Devices by Device ID Segment

If you need to add multiple access control devices which support ISUP 5.0 protocol and have no fixed IP addresses to the platform, you can add them all at once after configuring a device ID segment for the devices.

  • Make sure the devices you are going to add are correctly installed and connected to the network as specified by the manufacturers. Such initial configuration is required in order to be able to connect the devices to the HikCentral Professional via network.

  • Make sure you have activated the devices. Refer to Create Password for Inactive Device(s) for detailed instructions on activating devices.

  1. In the top left corner of Home page, select > Basic Management > Device.
  2. Select Device and Server > Access Control Device on the left.
  3. Click Add to enter the Add Access Control Device page.
  4. Select Hikvision ISUP Protocol as the access protocol.
    Note:

    Make sure you have enabled the ISUP protocol registration, otherwise the protocol will not be displayed. On the top, select System. Then, select Network > Device Access Protocol on the left, and switch on Allow ISUP Registration. Before adding devices by ISUP 2.6/4.0 protocol to the system, you need to check Allow ISUP of Earlier Version.

  5. Select Device ID Segment as the adding mode.
  6. Enter the required parameters.
  7. Optional: Switch on Picture Storage to set the storage location for pictures.

    • Select pStor and select storage locations for the face picture library and captured pictures.

      Note:

      This configuration only affects the facial recognition device which supports face comparison. The storage location of captured pictures and face picture libraries cannot be the same.

    • Select Local Storage as the storage location, click Configuration to enable Local Storage and set the storage locations for pictures and files as needed.

  8. Optional: Set the time zone for the device.
    Get Device's Time Zone

    The time zone of the device will be automatically chosen according to the region of the device.

    Manually Set Time Zone (The settings will be applied to the device automatically)

    You can select a time zone of the device. The settings will be applied to the device automatically.

  9. Optional: Switch on Add Resource to Area to import the resources (including alarm inputs, alarm outputs, and access points) to an area.
    Note:

    • You can create a new area by device name or select an existing area.

    • You can import all the access points or specific access point(s) to the area.

    • For the video access control terminal of a device, the camera on the terminal will also be imported to the corresponding area.

    • If you do not import access points to area, you cannot perform further configurations for the access point.

  10. Finish adding the device(s).

    • Click Add to add the device(s) and return to the device management page.

    • Click Add and Continue to add the device(s) and continue to add other devices.

  11. Optional: Perform further operations on the added device(s).
    Option Description

    Configure Device

    Click in the Operation column to enter the corresponding device configuration page to edit the time parameters, reboot the device, restore the device, or set other parameters. See Configure Device Parameters for detailed instructions.

    Change Password
    Select the added device(s) and click Change Password to change the password for the device(s).
    Note:

    • You can only change the password for online HIKVISION devices currently.

    • If the devices share the same password, you can select multiple devices to change the password together.

    Replace Device

    When a device is replaced with another one, and the serial No. of the new device is different from that of the old one, you need to confirm the replacement on the platform. In the Operation column, click to replace the old device with the new device on the platform.

    Restore Default Settings

    Select the added device(s) and click Restore Default Settings to restore the configured device parameters excluding network parameters and account information.

    Note:

    If you want to restore all the device parameters, you should check Restore device network parameters and account information, such as user name and password. in the pop-up window.

    Privacy Settings

    To protect the person's private information including the person's name and profile picture, you can configure privacy settings for online access control devices. For details, refer to Privacy Settings.

    Set Device's Time Zone

    On the device list, select one or multiple devices and click Time Zone to edit their time zones.

    Search for Devices

    Enter one or multiple key words in the search box and click to search for a specific device.